3DSolex CHT Matchless Nozzle 1.75 - 0,60mm

17 verfügbar
3DSolex CHT Matchless Nozzle 1.75 - 0,60mm
16,66 € *

inkl. MwSt. zzgl. Versandkosten

Sofort versandfertig, Lieferzeit ca. 1-3 Werktage

  • 17 verfügbar
  • 3dsol6nm
  • 7072482002035
  • 84779080
Fits: Raise3D N1 / N2 Nozzle diameter: 0,60mm Filament diameter: 1,75mm   Ramp up... mehr
Produktinformationen "3DSolex CHT Matchless Nozzle 1.75 - 0,60mm"

Fits: Raise3D N1 / N2

Nozzle diameter: 0,60mm

Filament diameter: 1,75mm

 

Ramp up plastic output thanks to our patented core heating nozzles and fully utilizing the Bondtech feeder already installed in your printer. By combining nozzle size, layer height and speed you can achieve up to 30 cubics / second.

Available Nozzles

0.25 mm (not Matchless, as the core heating will have little effect at the low throughput of this tiny nozzle)

0.40 mm (Matchless; core heating)

0.60 mm (Matchless; core heating)

0.80 mm (Matchless; core heating)

The nozzles are brass, and are coated with a layer to prevent them from reacting with the aluminium block.
This ensures that you can change nozzles without fear of destroying the heater block.

Tools

Recommended tool: Nozzle Changer for Prusa I3

What it does

This Nozzle allows “volcano-speeds” by just changing the nozzle (0.25 makes no difference). The Matchless nozzles, patented by 3D Solex, have a melting zone much bigger than an ordinary nozzle. An ordinary nozzle is melting the filament from the “outside” and trying to push the coldest part (centre of filament) through the exit hole of the nozzle.
The core heating effect of the Matchless nozzles is melting the middle  of the filament, that part which you wish to push out through the nozzle.

What the others must do: Lengthening the heating zone, which has a negative effect on retractions, adds weight to the head and is costly.

Advantages

1) You can now change nozzle risk free and hazzle free, by using the tool available separately. Change nozzle in seconds, without risk of destroying the sensors of the printer or the heat break.

2) Print with a much higher troughput, by configuring a combination of :

a) nozzle size

b) layer height

c) printing speed.

3) Print with a lower temperature. Since you are effectively melting the plastic you can print at a lower temperature than before. Using the existing settings of your previous print, you can lower 5-15 C.

4) Wide range of nozzles sizes (mm) available from 3D Solex:

0.25, 0.40, 0.50, 0.60, 0.80, 1.0, 1.2, 1.5, 2.0

Example: You can now print a vase with a 0.80mm nozzle at the same or higher speed than you could using a 0.40mm nozzle previously. This way you only need 1 pass to make a 0.8mm wall.

 

Weiterführende Links zu "3DSolex CHT Matchless Nozzle 1.75 - 0,60mm"
10 verfügbar
34 verfügbar
1 verfügbar
3 verfügbar
4 verfügbar
5-10 Tage Lieferzeit
5-15 Tage Lieferzeit
32 verfügbar
43 verfügbar
44 verfügbar
Capricorn XS-Serie PTFE-Bowdenschlauch für 1,75 mm Filament Capricorn XS 2 x 75cm 1,75mm...
Inhalt 1 Stück
29,75 € *
15-25 Tage Lieferzeit
5-10 Tage Lieferzeit
5-10 Tage Lieferzeit
5-15 Tage Lieferzeit
5-15 Tage Lieferzeit
- 5.12 %
Bundle Angebot
5-15 Tage Lieferzeit
3 verfügbar
- 9.52 %
TIPP!
Polymaker Polysmooth Filament Orange 750g Polymaker Polysmooth Filament Orange 750g
Inhalt 750 Gramm
ab 39,99 € * 44,20 € *
6 verfügbar
- 5.05 %
PolyMide_PA12-CF_Black_175 PolyMaker PolyMide™ PA12-CF Filament Black 500g
Inhalt 500 Gramm
ab 83,99 € * 88,46 € *
6 verfügbar
- 5.56 %
34 verfügbar
4 verfügbar
Zuletzt angesehen